Ovens

תנורים

*Prices are not including VAT and subject to changes in accordance with manufacturer prices  

WF - G  50L / 100L / 150L

Forced Convention Oven

4,900 ₪/6,500₪/8,000₪

WF-G Models is used for all sterilization and drying tasks that do not require high drying rates or special time requirements, ideal for drying applications requiring a gentle airflow.
• From +10℃ above room temperature to 260℃ .
• Microprocess PID control / Auto-tuning / Calibration.
• Digital timer: 1 min to 99 hr 59 min, delayed ON / OFF.
• Over temperature limit protection / Door opening alarm.
• Conveniently preset 3 most commonly used temperature settings without auto-tuning.
• Digital LED display (0.1℃ resolution) with touch keypads

Forced Convection Oven - 60L /100L /150L /250L

Forced Convention Oven

8,770 ₪ /8,950 ₪ /9,400 ₪ /14,300 ₪

• Uniform Temperature Distribution by Forced Convection of Heat Flow
• 5 Step Flow Control Prevent Spreading Sample
• Fan Stopping Function with Door Open for Minimize Temperature Change(Considering Safety of Operator)
• Observation Inside through Triple Tempered Glass Window without Door Open
• Upper Vent Hole for Venting Gases
• Simple and Intuitive User Interface with Graphic LCD Display
• Auto Tunning, Temperature Calibration Available
• Installation of RS485 PC Communication Device
• Emergency Stop Button for Immediate Shut Down
• Double Overheat Safety Device - 1st Controller Overheat Alarm, 2nd Overheat Shut Off Circuit
• 2 type of Timer Function Installed
• Automatical Fault Sensing System (By itself can detect an unusual situation.)

Forced Convention High Temp. Oven - 100L /150L

Forced Convention High Temp. Oven

14,900 ₪ /20,200 ₪

• Uniform Temperature Distribution by Forced Convection of Heat Flow
• Fan Stopping Function with Door Open for Minimize Temperature Change(Considering Safety of Operator)
• Highly Thermal Resistant Ceramic Packing Applied
• 50T Ceramic Temperature can be Raised Quickly through Insulation and High Heat Capacity
• 5 Step Flow Control Prevent Spreading Sample
• Installation of RS485 PC Communication Device
• Automatical Fault Sensing System (By itself can detect an unusual situation.)
• Double Overheat Safety Device - 1st Controller Overheat Alarm, 2nd Overheat Shut Off Circuit
• Simple and Intuitive User Interface with Graphic LCD Display
• Auto Tunning, Temperature Calibration Available
• 2 type of Timer Function Installed
• Programmable Controller
- Available to Set Operating Control Time for Temp. Increasing, Maintaining and Decreasing
- Available to Prevent Temperature Overshoot and Precision Temperature Control
- Available to Set and Repeat 2 Patterns/20 Segments Program

Muffle Furnace - 3L /4.5L /12L /14L /27L

Muffle Furnace

6,400 ₪ /6,950 ₪ /9,450 ₪ /9,750 ₪ /15,900 ₪

• Suitable for Researching with Drying, Plasticity, Batch Measuring, New Material and Ceramic Sintering
• Preventing Damages of the Heater from Contact of Vapor and Corrosive Gas by Installing Fire Proof Molded Heating Element
• Available to Rapid Temp. Increasing and Uniform Temp. Distribution by 3 Side Heating Walls inside Design
• Auto Tuning, Temperature Calibration, Self-diagnosis Function Available
• Installed Duct Hole for Exhaust Gas and Vapor inside
• Installed Safety Device for Circuit Protection from Over Current and Over Heat
• Installed Port for RS485 PC Communication.
• Automatical Fault Sensing System (By itself can detect an unusual situation.)
• Double Overheat Safety Device - 1st Controller Overheat Alarm, 2nd Overheat Shut Off Circuit
• Digital Over Temperature Safety Device
• 2 type Timer Function Installed
• Program Type (2 Pattern, 18 Segment)
- Program Set-up, Repetition and Operating Reservation.
- Saving Interlock with Increasing, Maintaining of Temperature and Operating Time, and Saved Program Operate Continuously